深圳市盈达顺科技有限公司 WINCOM TECH, 规格书

Wincom Tech CO., LTD.

The LCD(M) Specialist

CONTACT ADDRESS: 3F, Block 13, Wang Jing Keng Industrial Park,

DaKan, XiLi, NanShan, Shenzhen City, China.

PART NO. : FOR MESSRS. :

WO12864-GC-01 -SFYLYHC06(with PCB)

NO.

1. 2. 3. 4. 5. 6. 7. 8. 9. 10 11 12

COVER

RECORD OF REVISION GENERAL SPECIFICATION MECHANICAL DATA

ABSOLUTE MAXIMUM RATINGS ELECTRICAL CHARACTERISTICS OPTICAL CHARACTERISTICS OUTLINE DIMENSION BLOCK DIAGRAM

INTERFACE TIMING CHART INSTRUCTION CODE

SPECIFICATION OF QUALITY ASSURANCE

ITEM

PAGE 1 2 3 3 4 5 5 6~7 7 8-9 10 11~15

CONTENTS

ACCEPTED BY: PROPOSED BY:

深圳市盈达顺科技有限公司 WINCOM TECH, 规格书

RECORD OF REVISION

DATE 2012-4-27

PAGE ---

NEW ISSUE

SUMMARY

深圳市盈达顺科技有限公司 WINCOM TECH, 规格书

3. General specifications

3.1 General specifications

PLEASE REFER TO:

“CUSTOMER ACCEPTANCE STANDARD SPECIFICATIONS (MS-10-10000)”.

3.2 Quality Assurance and Warranty

PLEASE REFER TO:

“QUALITY ASSURANCE MANUL (MS-10-10001)“.

3.3 This individual specifiction is prior to general specifications

4. Mechanical data

Display format: 128 x 64 DOTS

LCD type: COG ,STN Positive Yellow-Green , Transflective Backlight color: LED, Yellow-Green Viewing angle: 6:00 Data transfer: 8Bit Parallel

LCD controller: ST7565R OR Equivalent Module size: 93.7 x 53.2 x 5.8mm View area: 70.7 x 38.8 mm Dot size: 0.48 x 0.48 mm Dot pitch: 0.52 x 0.52mm

Driving method: 1/65duty, 1/9 bias

Warning：Don’t clean the LCD or Backlight by liquid!

深圳市盈达顺科技有限公司 WINCOM TECH, 规格书

5. Absolute maximum ratings

5.1 Electrical absolute maximum ratings

I T E M

POWER SUPPLY FOR LOGIC INPUT VOLTAGE STATIC ELECTRICITY POWER SUPPLY FOR BACKLIGHT

STARTING VOLTAGE FOR BACKLIGHT

POWER SUPPLY FOR LCD ..

SYMBOL VDD-VSS VI --------- VS fFL ------ ------ Vlcd

MIN. -0.3 VSS ------ -0.3 ------ ------ ------ ------

MAX. 3.6 VDD ----- 2.3 ------ ------ ----- 9.0

UNIT V V V Vrms KHz Vrms Vrms V

COMMENT --------- --------- ----- --------- --------- Ta = 25℃ Ta = 25℃ ---------

5.2 Environmental absolute maximum ratings

I T E M AMBIENT TEMPERATURE HUMIDITY VIBRATION NOTE (3)

OPERATING MIN. MAX. -20℃

70℃

STORAGE

MIN. MAX. -30℃

80℃

COMMENT

------

NO

CONDENSATION 10~300Hz XYZ

DIRECTIONS 1 Hr EACH 10 msec XYZ

DIRECTIONS 1 TIME EACH

------

NOTE (2) NOTE (2)

------ 0.5G ------ 2G

SHOCK NOTE (3) CORROSIVE GAS

------ 3G ------ 5G

NOT

ACCEPTABLE NOT

ACCEPTABLE

NOTE (2): Ta ≦ 70℃: 75% RH MAX.

Ta ＞0℃: ABSOLUTE HUMIDITY MUST BE LOWER THAN THE HUMIDITY OF

75% RH AT 70℃.

NOTE (3): 1G = 9.8 m/s2

深圳市盈达顺科技有限公司 WINCOM TECH, 规格书

6. Electrical characteristics

I T E M

SYMBOL

CONDITION

------- ------

H LEVEL L LEVEL

Ta = 25℃ VDD = 3.3V MIN.

3.0

TYP. MAX. UNIT

3.3 9.0

3.4

V V V V

Power supply voltage for

VDD-VSS

circuit

Power supply voltage for LCD

VDD-VEE

drive

Data input voltage LCD display duty ratio

VIH VIL DUTY Ifp

-----

2.4

------

VDD

0.4

------ ------

1/64 -- 2.1 60

-0.3

------

I mseo plus 10% Dutg cyele Operating voltage Forward current VFL= 2.1Vrms fFL= KHz

------ 1.9

------ 2.2 70

------

mA V mA Hr

LED BACKLIGHT

LED Lifetime ------ ------ 100,000 ------

NOTE: LED backlight: Due to the LED backlight working current is XXX Max,and LED chips Vop may be different, Wincom will adjust the backlight resistor according to the LED chips Vop, to meet the brightness maximium.

7. Optical characteristics

I T E M

Viewing angle Contrast ratio

Ta = 25℃ VLCD = 9.0V

SYMBOL SYMBOL

Φ2-Φ1

K tr tf CONDITION CONDITION

K ≧ 2.0 Φ = 10 θ = 0 Φ = 10 θ = 0 Φ = 10 θ = 0

OOOOOO

MIN. TYP.MAX. UNITUNIT NOTENOTE MIN.TYP. MAX.

-35 4.0

----

20

deg.

1 1 1 1

---- ms ms

Response time

(at 25℃)

----- 250 ----- 250

The brightness

of backlighting source

B

VFL= 2.1Vrms

50 cd/m2 2

fFL= KHZ

NOTE (1): SEE CUSTOMER ACCEPTANCE STANDARD SPECIFICATION FOR DEFINITION

OF OPTICAL CHARACTERISTICS

NOTE (2): UNDER NORMAL TEMPERATURE AND HUMIDITY IN A DARK ROOM

深圳市盈达顺科技有限公司 WINCOM TECH, 规格书

8. Outline dimension

接触面

DOTS: 128 * 64

Wincom Tech. CO., LTD.

WO12864-GC-01 PAGE: 6/15 -SFYLYHC06(with PCB)

补强板

深圳市盈达顺科技有限公司 WINCOM TECH, 规格书

8.2Pin A s s i g n m e n tPIN NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 Red wire Black wire Symbol/CS/RES A0 WR RD DB0 DB1 DB2 DB3 DB4 DB5 DB6 DB7 VDD VSS VOUT CAP3+ CAP1CAP1+ CAP2+ CAP2V4 V3 V2 V1 V0 A K Leve 5.0V 0V H/L H/L H/L H/L H/L H/L H/L H/L H/L H/L H/L 3.3V 0V+10V --------------------2.1V/60mA 0V

Interface

Function Chip Selection Signal (Active" Low") Reset (Active" Low") Register select signal Data write Data read Data Bus Line Data Bus Line Data Bus Line Data Bus Line Data Bus Line Data Bus Line Data Bus Line Data Bus LinePower supply for logic circuit Ground

Output Voltage for LCD Driving For DC/DC voltage converter For DC/DC voltage converter For DC/DC voltage converter For DC/DC voltage converter For DC/DC voltage converter Power supply for the liquid crystal drive Power supply for the liquid crystal drive Power supply for the liquid crystal drive Power supply for the liquid crystal drive Power supply for the liquid crystal drive Power supply for BL LED(+) Power supply for BL LED(-)

9 Block diagram

Wincom Tech. CO., LTD.

WO12864-GC-01 PAGE: 7/15 -SFYLYHC06(with PCB)

深圳市盈达顺科技有限公司 WINCOM TECH, 规格书

10.Interface Timing Chart

深圳市盈达顺科技有限公司 WINCOM TECH, 规格书

Wincom Tech. CO., LTD.

WO12864-GC-01 PAGE: 9/15 -SFYLYHC06(with PCB)

深圳市盈达顺科技有限公司 WINCOM TECH, 规格书

11.Instruction Code

IC Specification: Please refer to

深圳市盈达顺科技有限公司 WINCOM TECH, 规格书

12. Specification of quality assurance

AQL inspection standard

Sampling method: MIL-STD-105E, Level II, single sampling Defect classification (Note: * is not including)

Classify Item

Short or open circuit LC leakage Flickering

Display state No display

Note AQL

1

0.65

2 1,8 10 11 2 3 4 5 6 7 12 3 9 10 13

1.0

Major Wrong viewing direction Contrast defect (dim, ghost) Back-light

Flat cable or pin reverse

Non-display

Wrong or missing component Background color deviation Black spot and dust Line defect, Scratch

Display state

Rainbow Chip

Minor

Polarizer

Pin hole Protruded

Bubble and foreign material

Soldering Wire TAB

Poor connection Poor connection

Position, Bonding strength

深圳市盈达顺科技有限公司 WINCOM TECH, 规格书

Note on defect classificationNo.

Item Short or open circuit LC leakage Flickering

Criterion

1

No display Wrong viewing direction Wrong Back-light Contrast defect

Not allow

2 Backgroundcolor deviation Point defect, Black spot, dust (including Polarizer)φ= (X+Y)/2

Refer to approval samplePoint Sizeφ<0.10 0.10<φ≤0.20 0.20<φ≤0.25 0.25<φ≤0.30 Y Xφ>0.30 Unit:mmLine L W0.015≥W 0.03≥W .05≥W 0.1>W0.05<W

Acceptable Qty. Disregard 3 2 1 0

3

Acceptable Qty.

4 Scratch

Line defect,W L

--3.0≥L 2.0≥L 1.0≥L

Disregard

2 1Applied as point defect

---

5 Rainbow

Not more than two color changes across the viewing area.

Wincom Tech. CO., LTD.

WO12864-GC-01 -SFYLYHC06(with PCB)

PAGE: 12/15

深圳市盈达顺科技有限公司 WINCOM TECH, 规格书

NO. 6

Item Chip Remark: X: Length direction Y: Short direction Z: Thickness direction t: Glass thickness W: Terminal Width

Criterion

Acceptable criterion X Y Z 0.5mm≤t/2≤2

Acceptable criterion X Y Z 0.5mm≤t≤2

Acceptable criterion X Y Z≤3≤2≤t shall not reach to ITO

Acceptable criterion X Y Z Disregard≤0.2≤t

Wincom Tech. CO., LTD.

WO12864-GC-01 -SFYLYHC06(with PCB)

PAGE: 13/15

深圳市盈达顺科技有限公司 WINCOM TECH, 规格书

No. 7

Item Segment pattern

W = Segment width φ = (X+Y)/2

Criterion (1) Pin hole

φ < 0.10mm is acceptable.

8 Back-light

(1) The color of backlight should correspond its specification. (2) Not allow flickering

(1) Not allow heavy dirty and solder ball on PCB.

(The size of dirty refer to point and dust defect)

(2) Over 50% of lead should be soldered on Land.

9 Soldering

10

Wire

(1) Copper wire should not be rusted (2) Not allow crack on copper wire connection.

(3) Not allow reversing the position of the flat cable.

(4) Not allow exposed copper wire inside the flat cable.

(1) Not allow screw rust or damage.

(2) Not allow missing or wrong putting of component.

11* PCB

深圳市盈达顺科技有限公司 WINCOM TECH, 规格书

NO. Item

12 Protruded

W: Terminal Width

Criterion

Acceptable

criteria:

Y ≤ 0.4

1. Position

W1≤1/3W H1≤1/3H

2 TAB bonding strength test

P (=F/TAB bonding width) ≥650gf/cm , (speed rate: 1mm/min) 5pcs per SOA (shipment)

13 TAB

14

Total no. of acceptable Defect

A. Zone

Maximum 2 minor non-conformities per one unit.

Defect distance: each point to be separated over 10mm B. Zone

It is acceptable when it is no trouble for quality and assembly

in customer’s end product.