元器件交易网http://

Embedded Power for

Business-Critical Continuity

Rev. 2.18.09_133

HPS35 Series

1 of 4

元器件交易网http://

Module Information

Environmental Specifications

Rev.2.18.09_133HPS35 Series

2 of 4

元器件交易网http://

Rack Information

Racks

Rev. 2.18.09_133

HPS35 Series

3 of 4

617-A-037-P-AJ-1-21 (Male socket) Amphenol

Pin Out Diagram D-sub Connector (male)

Mating Connector

617-A-037-S-AJ-1-20 (Female socket) Amphenol

Pin Out Diagram D-sub Connector (female)

元器件交易网http://

D. Sub Connector Additional Notes

Pin 2 + Remote SenseDC OK (OUT Signal)

Pin 3 - Remote Sense

Compensates for up to 0.5V drop. Recommended shielded twisted wire pair.

Pin 12 - Global AC OK (OUT signal)

Note: DC OK signals for each slot in the rack is accessible in the D-sub

connector (J18). Refer to Connector Pin-out table for pin assignments. Pin 1 is the Return Pin.

Note: AC OK signals are OR’ed together AC OK (OUT Signal)internally. If any module fails, the LED on the affected module will be off and the logic signal will indicate AC NOT OK.Pin 19 - Global Inhibit (IN signal)

Note: AC OK signals for each slot in the rack is accessible in the D-sub

connector (J18). Refer to Connector Pin-out table for pin assignments. Pin 1 Note: All outputs disabled when Pin 19 is the Return Pin.

is open or High.

Hi state: Source 100uA @ 4VPin 22 - SWP (IN/OUT signal)

Low State: Sink 10mA @ 0.5V

PIN 22

SWP Pin is used when

connecting racks in Fan Monitor (OUT Signal)parallel to achieve

PIN 3

current sharing. Current

share accuracy is

typically 10% of full load.Note: SWP Voltage is 5V at 100% load current.

Module Inhibit (IN Signal)

Note: Fan Monitor signals for each slot in the rack is accessible in the D-sub connector (J18). Refer to Connector Pin-out table for pin assignments. Pin 1 is the Return Pin.

I2C_ADD#1

Note: Module Inhibit signals for each I2C_ADD#2slot in the rack is accessible in the D-sub TBDconnector (J18). Refer to Connector Pin-out table for pin assignments. Pin 1 is the Return Pin.

Embedded Power for

Business-Critical Continuity

Rev.2.18.09_133HPS35 Series

Americas

4 of 4

5810 Van Allen WayCarlsbad, CA 92008USA

Telephone: +1 760 930 4600Facsimile: +1 760 930 0698

Europe (UK)

Waterfront Business ParkMerry Hill, Dudley

West Midlands, DY5 1LXUnited Kingdom

Telephone: +44 (0) 1384 842 211Facsimile: +44 (0) 1384 843 355

Asia (HK)

14/F, Lu Plaza2 Wing Yip StreetKwun Tong, KowloonHong Kong

Telephone: +852 2176 3333Facsimile: +852 2176 3888

For global contact, visit:

http://techsupport.embeddedpower@http://

While every precaution has been taken to ensure accuracy and completeness in this literature, Emerson Network Power assumes no responsibility, and disclaims all liability for damages resulting from use of this information or for any errors or omissions.

Emerson Network Power. The global leader in enabling business-critical continuity.

AC PowerConnectivityDC Power

Embedded ComputingEmbedded PowerMonitoringOutside Plant

Power Switching & ControlsPrecision Cooling

Racks & Integrated CabinetsServicesSurge Protection

http://

Emerson Network Power and the Emerson Network Power logo are trademarks and service marks of Emerson Electric Co. ©2008 Emerson Electric Co.