HP BladeSystem c7000 安装配置手册

HP BladeSystem c7000 安装配置手册

HP BladeSystem c7000 Enclosure

Quick Setup Instructions

Part Number 411762-007

February 2010 (Seventh Edition)

HP BladeSystem c7000 安装配置手册

Verifying the pallet contents

HP BladeSystem c7000 安装配置手册

* Not shown

Installing the enclosure

WARNING: Because the fully-populated enclosure can weigh up to 217.7 kg (480 lb), remove all components and the rear cage from the enclosure before removing the enclosure from the pallet to reduce the risk of personal injury when moving the enclosure.

CAUTION: When removing the rear cage and

midplane assembly, the connectors on the midplane assembly are susceptible to damage. Use caution to avoid damage to the pins and connectors.

CAUTION: Be sure the hinges are completely open before installing the rear cage into the enclosure. Failure to do so can cause damage to pins and connectors.

1.

The enclosure can be installed in a rack or rack-free

environment. Select the proper location based on requirements detailed in the HP BladeSystem c7000 Enclosure Setup and Installation Guide.

2.

Remove all components from the front and rear of the enclosure, and then remove the rear cage.

HP BladeSystem c7000 安装配置手册

3.

(Optional) Install the enclosure into a rack. See the HP

BladeSystem c7000 Enclosure Rack Template. For rack-free installations, omit this step.

4.

Install the rear cage into the enclosure, close the hinges, and

tighten the thumbscrews.

Enclosure bay identification

Before installing front or rear components into the enclosure, review enclosure bay numbering for each component.

Full-height device bay numbering

Half-height device bay numbering

Power supply bay numbering

HP BladeSystem c7000 安装配置手册

Fan bay numbering

Installing the front components

CAUTION: To prevent improper cooling and thermal damage, do not operate the enclosure unless all bays are populated with a component or a blank.

CAUTION: Do not mix HP 2250W, HP 2400W High Efficiency, HP BL7000 2400W Platinum, or -48vDC power supplies in one enclosure. Install only one type of power supply in a single enclosure.

If your HP BladeSystem c7000 Enclosure is equipped with a three-phase power configuration, you need six power supplies. To install a power supply: 1. To gain access to all power supply bays, slide the HP BladeSystem Insight Display to the right or left as needed. 2. Remove the power supply blank.

3.

Insert the power supply into the enclosure, and then close the

power supply bracket.

NOTE: This document discusses installation of AC

power supplies only. For information on configuring DC power supplies or HP Carrier Grade Solutions, see the documentation that came with your power supply.

4. Add any ordered options to each server blade: o Additional processor o Additional memory o Mezzanine option cards

5.

(Optional) If you are installing a full-height device, remove the half-height device bay shelf. If you are installing a half-height

device, omit this step.

6. Remove the connector covers. 7. Install the server or storage blades.

8.

Install device bay blanks into any unused device bays. If the empty bays are configured for a full-height device, join

two device bay blanks to create a full-height blank.

HP BladeSystem c7000 安装配置手册

Installing the rear components

CAUTION: To prevent improper cooling and thermal damage, do not operate the enclosure unless all bays are populated with a component or a blank.

1.

Install fans in even-numbered groups, based on the total number of blades installed in the enclosure:

o Four fan configuration—Fan bays 4, 5, 9, and 10 are

used to support a maximum of two devices located in device bays 1, 2, 9, or 10. Only two device bays can be used with four fans. o Six fan configuration—Fan bays 3, 4, 5, 8, 9, and 10 are

used to support devices in device bays 1, 2, 3, 4, 9, 10, 11, or 12. o Eight fan configuration—Fan bays 1, 2, 4, 5, 6, 7, 9, and

10 are used to support devices in all device bays. o Ten fan configuration—All fan bays are used to support

devices in all device bays.

NOTE: When installing a fan in the top row of fan bays, orient the fan so that the LED is in the lower right corner. When installing a fan in the bottom row of fan bays, orient the fan so the LED is in the upper left corner.

2. Install fan blanks in any unused fan bays.

3.

Install the Onboard Administrator with KVM modules into the Onboard Administrator with KVM tray based on the total number ordered:

o One Onboard Administrator with KVM module: Bay 1 o Two Onboard Administrator with KVM modules: Bays 1

and 2

Install an Onboard Administrator with KVM blank into any

unused Onboard Administrator with KVM bay.

Connecting the cables

1.

Identify all connectors.

HP BladeSystem c7000 安装配置手册

2.

To connect to the management network, connect a standard CAT5 patch cable to the OA/iLO port of each installed Onboard Administrator with KVM module.

3.

If more than one enclosure is installed in the rack, use a CAT5 patch cable to connect the enclosure link-down port on the upper enclosure to the enclosure link-up port on the lower enclosure.

NOTE: The enclosure link ports are designed only to support c-Class enclosures in the same rack. The

enclosure link-up port on the top enclosure is the service port, and the …… 此处隐藏：13420字，全部文档内容请下载后查看。喜欢就下载吧 ……