扫描枪设置-Honeywell-4600

4600g, 4600r, 4600rp, 4800i

Quick Start Guide

Note:Refer to your user’s guide for information

about cleaning your device.

For localized language versions of this document, go to http:///aidc.

Getting Started

Turn off computer’s power before connecting the scanner, then power up the computer once the scanner is fully connected.

USB Connection

1

Keyboard Wedge Connection

Serial (RS-232) Connection

2

Reading Techniques

The view finder projects an aiming beam that should be centered over the barcode, but can be positioned in any direction for a good read.

Hold the scanner over the barcode,

pull the trigger, and center the aiming beam on the barcode.

The aiming beam is smaller when the scanner is closer to the code and larger when it is farther from the code. Hold the scanner close to smaller

barcodes, and farther away from large barcodes to get a proper read.

If the barcode is highly reflective (e.g., laminated), you may need to tilt the scanner at an angle so the barcode can be scanned.

Standard Product Defaults

The following barcode resets all standard product

default settings.

Standard Product Defaults

3

Interface

Scan the barcode that describes the PC or interface

you are using.

USB Keyboard (PC)

RS-232

Japan DOS/V

USB Japanese Keyboard (PC)

AT/PS2 Keyboard Wedge

(Default)

Emulate External Keyboard

4

Keyboard Country

Scan the Program Keyboard Country barcode below, then scan the numeric barcode(s) from page 10, then the Save barcode to program the keyboard for your country. As a general rule, the following characters are not supported by the

scanner for countries other than the United States: @ | $ # { } [ ] = / ‘ \ < > ~.

Program Keyboard Country

Country CodeBelgiumDenmark

Finland

France

Germany/AustriaGreat Britain

Scan182347

Country CodeItalyNorwaySpainSwitzerlandUSA (Default)

Scan

591060

Save

Note:For a complete list of country codes, see the

User’s Guide for your product at our website, http:///aidc.

5

Trigger

The following barcodes will allow you to use the reader in Manual Trigger mode (need to press the trigger to read) or Presentation mode (the reader is activated when it “sees” a barcode).

Manual Trigger(Default)

Presentation Mode

Streaming Presentation

Note:Streaming Presentation Mode applies only

to units with the Advanced Illumination

feature. Units with the advanced illumination feature have a software revision of 31205480-118 or newer.

When in Streaming Presentation mode, the imager leaves the scan illumination on all the time and

continuously searches for barcodes.

Streaming Presentation Mode

6

Reread Delay

This sets the time period before the scanner can read the same barcode a second time. Setting a reread delay protects against accidental rereads of the same barcode.

Medium Reread Delay

Suffix

If you want a carriage return after the barcode, scan the Add CR Suffix barcode. To add a tab after the barcode, scan the Add Tab Suffix barcode. Otherwise, scan the Remove Suffix barcode to

remove the suffixes.

Add CR Suffix

Add Tab Suffix

Remove Suffix

7

Add Code ID Prefix to all Symbologies

Scan the following barcode if you wish to add a Code ID prefix to all symbologies at once.

Add Code ID Prefix To All Symbologies

(Temporary)

Note:For a complete list of Code IDs, see the

User’s Guide for your product at our website, http:///aidc.

Function Code Transmit

When this selection is enabled and function codes are contained within the scanned data, the imager transmits the function code to the terminal. Charts of these function codes are provided in your User’s Guide. When the imager is in keyboard wedge mode, the scan code is converted to a key code

before it is transmitted.

Enable(Default)

Disable

8

Data Format Editor Instructions

The following are abbreviated instructions for entering a data format. For complete instructions refer to your User’s Guide, available at our website, http:///aidc.

1.Scan the Enter Data Format symbol.2.Primary/Alternate Format: scan 0 for Primary

Format3.Terminal Type: scan 099 for any terminal type4.Code I.D.: scan 99 for any barcode type5.Length: scan 9999 for any length barcode.6.Editor commands: use the Programming Chart

that follows.7.Scan Save

to save your entries.

Enter Data Format

Clear All Data Formats

Save

9

Programming Chart

1

2

3

4

5

6

7

10

8

9

A

B

C

D

E

F

Save

11

Visual Xpress

To obtain access to additional features for the imager, use Visual Xpress, available from our

website at http:///aidc. For complete download instructions and descriptions of Visual Xpress features, refer to your User’s Guide.

Technical Assistance

If you need assistance installing or troubleshooting your device, please call your distributor or the nearest technical support office:

North America/Canada

Telephone: (800) 782-4263

(8 a.m. to 6 p.m. EST)

Fax number: (315) 554-6705

E-mail: natechsupport@http://Latin America

Telephone: (803) 835-8000 Telephone: (800) 782-4263

E-mail: latechsupport@http://Brazil

Telephone: +55 (21) 3535-9100 Fax: +55 (21) 3535-9105

E-mail: brsuporte@http://Mexico

Telephone: (803) 835-8000

E-mail: latechsupport@http://Europe, Middle East, and AfricaTelephone: +31 (0) 40 7999 393 Fax: +31 (0) 40 2425 672 …… 此处隐藏：5583字，全部文档内容请下载后查看。喜欢就下载吧 ……