目录

5.2.4 5.2.5

B-64304CM-2/01

固定循环取消 (G80)..........................................................................................................................81 刚性攻丝中的倍率............................................................................................................................81

5.2.5.1 5.2.5.2

拉拔倍率..............................................................................................................................................81 倍率信号..............................................................................................................................................83

5.3 5.4 5.5 5.6

任意角度的倒角/拐角R....................................................................................................................84 分度台分度功能.................................................................................................................................88 横向进给控制(磨床用)......................................................................................................................91 磨削用固定循环（磨床用）.............................................................................................................94 5.6.1 切入式磨削循环(G75).......................................................................................................................96

5.6.2 5.6.3 5.6.4

切入式直接恒定尺寸磨削循环 (G77)............................................................................................100 连续进给表面磨削循环(G78).........................................................................................................104 间歇进给表面磨削循环 (G79)........................................................................................................108

6 补偿功能...............................................................................................................................111

6.1

刀具长度补偿（G43, G44, G49）..................................................................................................112 6.1.1 概要..................................................................................................................................................112

6.1.2

刀具长度补偿中的G53, G28, G30指令........................................................................................118

6.2

6.3 6.4 6.5 6.6

刀具长度补偿偏移类型...................................................................................................................120 刀具长度自动测量（G37）............................................................................................................128 刀具位置偏置（G45～G48）.........................................................................................................131 刀具半径补偿（G40～G42）的概括说明.....................................................................................136 刀具半径补偿的详细说明...............................................................................................................143 6.6.1 概要..................................................................................................................................................143

6.6.2 6.6.3 6.6.4 6.6.5 6.6.6

起刀时的刀具移动..........................................................................................................................147 偏置方式下的刀具移动..................................................................................................................153 偏置方式取消方式下的刀具移动...................................................................................................172 利用刀具半径补偿来防止过切.......................................................................................................179 干涉检测..........................................................................................................................................182

6.6.6.1 6.6.6.2 6.6.6.3

被判断为干涉时的动作....................................................................................................................185 干涉检测报警功能............................................................................................................................186 干涉检测回避功能............................................................................................................................187

6.6.7

针对来自MDI输入的刀具半径补偿.............................................................................................193

6.7 6.8 6.9 6.10 6.11 6.12 拐角圆弧插补（G39）....................................................................................................................195 刀具补偿量、补偿量数目和利用程序的刀具补偿量输入（G10）.............................................197 比例缩放(G50,G51)..........................................................................................................................200 坐标旋转（G68、G69）.................................................................................................................208 法线方向控制(G40.1,G41.1,G42.1).................................................................................................216 可编程镜像（G50.1, G51.1）.........................................................................................................221

7 8

Series 10/11格式下的存储器运行.....................................................................................223 轴控制功能...........................................................................................................................224

8.1

电子齿轮箱（G80, G81（G80.4, G81.4））..................................................................................225 8.1.1 电子齿轮箱......................................................................................................................................225

III. 操作

1

显示和设定数据

235

1.1

1.1.1 1.1.2

.........................................................................................................236

显示和设定刀具偏置量..................................................................................................................237 刀具长度测量..................................................................................................................................240