手机可靠性测试标准

,MISCELLANEOUS手机可靠性测试标准,包括AGGRAVATED ENVIRONMENT ART,SIM Card /TF Card,ART AGEING,CLIMATIC CONDUCTED,ART MECHANICAL TEST,AESTHETIC and COSMETIC TEST,SPECIAL ENVIRONMENT ART,PACKAGE ART ,SPECIAL Test for PARTS & ACCESSORIES

Product Qualification PlanN° 1 1.1 TEST FAMILY DESCRIPTION/Set up Product Status During Test & Purpose ACCEPTANCE CRITERIAS PR1 Qty 1)50% of the samples with their front facing the "equipment floor" 2)50% of the samples with their back facing the "equipment floor" 3)The product is switched off 4) For Clamshell /Slidering products ,the test units are in both positions: Closed and Opened. Product must be fully functional, No binding or blocking of moving parts. No accumulated dust under viewing areas preventing normal product operation. Keypad detection OK. Keypad Back light may be altered, Camera performance may be altered. 功能和外观必须正常,可移动部件移动顺畅.没有堆集的 灰尘在LCD,camera里面可视部位,按键和摄像功能正 常. PR2 Qty Pil Qty

AGGRAVATED ENVIRONMENT ART Dust Refer to GB 2423.37-89: 15-35° 8h,fill 2kg dry talcum powder, dust free drops in C chamber -chamber temp/humidity : 15~35oC, 45%~75%RH -Duration:8h -Max air velocity :2m/s -dust concentration :2Kg /m3

2

2

2

1.2

Salt fog

Refer to MIL-STD-810F: '35° 48h 5% NaCl salt fog concentration 48h drying time: C o o -Temprature inside the camber :+/-35 C+/-2 C -Humidity inside in the chamber:85% RH -Quantity of solution collected on an horizontal surface of 80cm2 shall be between 2+/-1ml/h -NaC1concentratoin :5% in weight -Ph=7-0.5+0.2 -Duration:48 h Drying period:48h

1) The product is switched off . 2) Half samples is in stand up position with antenna up.Half samples is in stand up position with antenna down. 3) For Clamshell /Slidering products ,the test units are in both positions: Closed and Opened. 4)with dummy battery

The product should be functional after salt fog test , but any corrosion must be analysed for its immediate and potential long-term effects on the proper functioning and structural integrity of the test item for making final assessment. Partial or complete disassembly of the test item need to be performed for a complete visual examination. 如果产品功能正常，要拆机检查是否有腐蚀状况，评 估风险。如果有腐蚀情况并且有恶化风险，则判定为 失败。 如果功能不正常，要检查是否是因为腐蚀而造成的失 效。如果是，则判定失败。

2

2

2

1.3

Rain shower

5min 0,01m3/min, 90Kpa then 24h drying time

1)Power on Mode, with battery, no SIM card Fully functional after 24h drying time 2)For Clamshell/ Slidering products ,one will be tested 自然放置，室温，24小时，功能正常。 in closed and the other in opened positon. 3)For bar phone, 1pc top surface towards outside,1pc on back surface .

2

2

2

2

MECHANICAL ENDURANCES 8N actuation force , 60cy/min, press time 0,2s, 500k. The Power off Mode , with battery, no SIM card. clic feeling (F1, F2 force) is measured @begin & end of test Fully functional, all keys function ok and also good tactile feeling .A decrease of the click feeling of 20% is the max acceptable. 功能与外观均正常，手感最

多允许降低20%。 Fully functional, all keys function ok and also good tactile feeling .A decrease of the click feeling of 20% is the max acceptable. 功能与外观均正常，手感最多允许降低20%。

Keypad Endurance 2.1 Keypad

2

4

2

2.2

Side key

8N actuation force , 60cy/min, press time 0,2s,100k. The Power on Mode , with battery, no SIM card. clic feeling (F1, F2 force) is measured @begin & end of test

(2)

(4)

(2)

Flip/Slide Endurance 2.3 Clam shell 100k, open/close, 30cycles/minutes. Power on Mode , with battery and charger ,no SIM card. Fully functional. Detection working properly. Gaps between parts may increase. (max.30%). 外观与功能正常，翻盖间隙在100k后，可以适度增 大，但不可超过原始的30%

4

4

2

,MISCELLANEOUS手机可靠性测试标准,包括AGGRAVATED ENVIRONMENT ART,SIM Card /TF Card,ART AGEING,CLIMATIC CONDUCTED,ART MECHANICAL TEST,AESTHETIC and COSMETIC TEST,SPECIAL ENVIRONMENT ART,PACKAGE ART ,SPECIAL Test for PARTS & ACCESSORIES

2.4

Slide

100K open/close cycles,40times/min

Power on Mode , with battery and charger ,no SIM card.

Fully funcitonal during and after test, Slight decrease of operating force is tolerate lost forces after 100K max 30%. 外观与功能正常，滑盖在100k后，滑盖操作力度不得 比原始下降30%。

Touch Panel /stylus 2.5 Hitting durability 1000K times on the same point , 250gf +/- 10%, 1time /1s, test 2 points at least 1)Power on Mode , with battery and SIM card. 2)Tip of stylus is R0.8mm(min) 1) Fully functional 2) No breakage on the surface of touch panel. 3) Linearity \Terminal resistance\insulation of touch panel iswithin its spec. 1)功能与外观正常 2)触屏表面无裂纹 3)触屏的线性、端电阻值/绝缘性能在规格之内 1) Fully functional 2) No breakage on the surface of touch panel. 3) "Sliding trace" or "Hitting trace on touch panel after test is acceptable. 4) Linearity \Terminal resistance\insulation of touch panel iswithin its spec. 1)功能与外观正常 2)触屏表面无裂纹 3)触屏的线性、端电阻值/绝缘性能在规格之内 2.7 Stylus in/out cycles 50K times in/out cycles Power off Mode ,no Sim card and battery 1) No damage on the stylus and mobile plastic. 2) Stylus in/out smoothly and also no loose 1)触笔无损坏 2)插拔顺利，不能太松

2

2

2

2.6

Pen sliding durability

100k times ,250gf +/- 10%, 60mm/1s,writing length …… 此处隐藏：22535字，全部文档内容请下载后查看。喜欢就下载吧 ……