KTV灯光音响安装详细步骤介绍

KTV灯光音响安装详细步骤介绍
关键词：舞台灯光，灯光安装，灯光音响工程，舞台设备，装饰，KTV装潢，舞台搭建
文章来源：舞台灯光网

　　见过很多KTV效果图，发现它们一大共同点，那就是灯光效果做的都很到位，甚至很多KTV都是在依靠灯光制造氛围。由此可见灯光的安装何等重要。音响可以说是KTV的灵魂，没有很好的音响设备很难吸引顾客的光顾。KTV装修设计基本的装潢自然重要，灯光音响的安装要是一大难点和重点，下面就介绍一下灯光音响安装的步骤，好让各位在安装自己的场所时不至于方针大乱。

　　一、首先灯光音响工程要进行管线和挂接件的预埋。管线和挂接件的预埋一般需要在灯光音响工程项目确定后就应该马上开始，因为通常来讲，预埋的管线主要都在没有的舞台搭建、或没有装饰的地面豚墙面里，如果不及时进行预埋，就很容易影响装饰工程的进度，主要是穿线施工方便，容纳的线缆量较大，又能防火；对于埋设距离较长的管线，一定要在一定的距离开设检修口，最后必须注意的是，预埋管线的工作几乎是无法更改的，一旦决定了在什么地方，埋多少，怎么埋，而且预埋完工后，要想更改就不太可能了，所以预埋前一定要认真地分析设计，明确设备的数量、位置、供电情况及控制方式，在此基础上提出准确的管线数量、口径和走向。

　　二、其次要进行各种葡萄架的焊接和安装。这项工作尽量与装饰工程交叉进行，因为在施工中难免开启一些孔洞以及对已有的装饰物产生破坏，这些都需要装饰部门协助完成，在焊接的过程中，一定要让具有焊接资格的工人操作，这样做除了方式安全的要求外，主要是焊接质量直接关系到棚架的吊装强度，不能马虎，同时，因为焊接施工通常都是与装饰工程同时进行的，现场会有一些易燃物，所以施工中一定要注意防火，待焊接牢固，油漆完成后，就应该开始这些棚安装了，安装的安全性同样非常重要，必须有建筑技术人员比较充足的时候才能开始吊装；最后就是，所有的安装件都必须增设可靠的保护措施，这样的安装才有安全的保证。

　　三、再下面就要进行各种线缆的铺设。这项工作虽然比较简单，但是也应该认真进行，特别是穿管
这一项，容不得一点马虎，铺设线缆道德要掌握合理的方法，例如穿管时钢丝与要穿的线缆应该捆扎牢固，扎头要得减小阻力，必要时涂抹少量的润滑油；其次线缆损坏或错乱的麻烦；再者就是要在线缆铺设时认真对线缆进行检查，象外皮是否破裂，屏蔽层是否损坏以及芯线是否断裂等等；最后，一定要在铺设的线缆上做好明

KTV灯光音响安装详细步骤介绍

显的标记，以备安装设备和日后检修时使用。

　　四、再后面应该进行各种舞台设备的安装。舞台设备的安装必须在装饰完工、线缆铺设正确后进行，国为音响灯光设备不仅价格较贵，而且许多设备需要避免尘土的沾染，装饰工程凌乱的现场是不适合安装设备的，设备的安装首先应该注意开箱时要仔细检查，因为许多国外设备的包装非常规范，有一些重要的备件或说明书可能单独隔离在包装盒的底层，很容易在拆箱时随包装盒一起扔掉；其次设备安装前应该认真阅读产品说明书，以掌握正确的安装方法、步骤。例如；许多电脑灯的灯泡和镀膜玻璃都要求佩带棉线手套安装，不允许直接用手去接触；最后就是设备安装要牢固，保护措要完备，特别是灯光设备，位置高、重量大而且以常运动，一般又在舞台或舞池的上方，所以必须绝对确保安全。

　　五、最后就是供电线路，控制线路和信号线路的连接。这是一项需要细致认真和技术性的工作，所以应该由技术过硬责任心强的人员进行，在线路的连接时，首先要求方式必须确保在无电状态下进行，因为音响灯光设备的电源供应要求不尽相同，如果在安装时就提供电源，不仅安全性差，而且很容易损坏设备
其次，要求施工符合电器安装规范，因为电器安装规范是检验方式是否合理的标准，所以按照规范施工与否，达到期的工程质量是完全不同的，许多按照规范施工的正规的工程内行一看就知道活儿干得“漂亮”。
　　 从屏蔽来讲，系统网络抗干扰的能力，主要决定于系统屏蔽是否正确及屏蔽是者不工作，重者就会损坏设备，而供电线路相位的错误则可能会影响到音箱的相位，从而否正确及屏蔽质量的高低，常常在一些工程中发现：要么没有进行屏蔽，要么屏蔽层形成闭环回路；要么就是屏蔽线连接错误没有形成屏蔽网络抵抗不了干扰，甚至有些工程的施工人员将信号地和电源的零、地、屏蔽线和信号线这几个要领混淆，胡乱连接，不光抗不了干扰，还会带来大量的干扰，所以一定要先实实在在地把这些概念理解清楚。

　　六、另外就是对安装、供电线路、连接情况的检查。因为音响工程的整个系统涉及的连接点和插接件比较多，在安装时也有可
能因为个别的原因发生错误，所以，细致的检查是有必要的，一般的检查包括设备安装安全性，供电线路是否合理，各插接件的连接是否正确等，另外还有一个重要的检查项目就是：仔细检查每一件设备的状态设置是否满足设计要求，这点绝对不能忘记，否则极易造成设备损坏，这些状态包括；功放在桥接要求时，桥接开关是

KTV灯光音响安装详细步骤介绍

否置位；各设备的电源选择开关是否合适；灯光设备是声控还是电控；电脑灯的地址码是否设置正确；投影机的输入方式设置等等。

　　七、待以上施工步骤都确信完成后，就应该准备进行设备的调试了。对于设备的调试，因为各个工程的情况不同，很难统一一个通用的方法，需要单独分类进行讨论，如果要想完整地全面地对所有类型的工程调试过程进行介绍，篇幅会太大，下面只就一般的工程设备调试简单进行介绍。



KTV lighting and sound installation steps described in detail
Keywords: stage lighting, lighting installation, lighting and sound engineering, stage equipment, decoration, KTV decoration, stage construction

KTV effects seen many plans and found them a big thing in common, that is, to do lighting effects are in place, and even many KTV are relying on light manufacturing environment. This shows how important the installation of lighting. KTV audio can be said of the soul, there is no good audio equipment is difficult to attract customers to patronize. KTV decoration decoration natural essential importance of the installation of lighting and sound and if the focus of a major difficulty, to brief the following steps to install lighting and sound, so you install your own place in the principle of chaos when the Buzhi Yu.

First, the first of the line lighting and sound engineering to mount parts embedded. Pipeline and attached pieces of lighting and sound embedded in general need to identify the project should be immediately after the start, because generally speaking, are embedded in the absence of the main pipeline of the stage construction, or no decoration dolphin wall in the ground, if not embedded in time, it is likely to influence the progress of decoration, mainly threading to facilitate the construction to accommodate a large amount of cable, but also fire; for long distance laid pipeline, a certain distance must be set up in the manhole Finally should be noted that the work is almost embedded pipeline can not be changed, once decided where, how much buried, how buried and embedded after the completion, in order to change is unlikely, so embedded ago must carefully analyze the design, a clear device number, location, power supply and control the situation, put forward on this basis, the exact line number, diameter and direction.

Second, and secondly to carry out the welding and installation of a variety of vine. The work carried out as cross and decoration works, as is inevitable in the construction of a number of open holes and the decorations have been damaged, they need to help complete the decorating department, in the welding process, we must allow qualified workers with welding operation, this means the safety requirements
in addition to the main welding quality is directly related to the scaffolding lifting strength, can not be careless at the same time, because t

KTV灯光音响安装详细步骤介绍

he welding construction and decoration works are usually the same time, the site will have some combustible material, Suoyi construction must observe the fire until the welding firm, Youqi completed, you should begin these Peng installed, the installation of security is also very important to have a more adequate building technology staff time to begin Diaozhuang; last is, of all mounting must be secure additional protective measures, such installations have a security guarantee.

Third, again following a variety of cable laying will be carried out. This work is a relatively simple, but it should also be seriously, in particular, to wear out of this one, can not tolerate a little sloppy, the laying of cables to grasp the moral and reasonable, for example, pipe wear and wear of the cable wire should be tied securely , bar-head quest reduce the resistance, if necessary, apply a small amount of oil; followed by cable damage or disorder of the trouble; Furthermore, is the time to carefully lay the cable to check the cable, like the skin is broken, the shield is damaged and the wire is broken and so on; Finally, we must do a good job in laying the cable was on the mark, in order to repair the installation of equipment and future use.

Fourth, and then should be followed by various stage equipment installation. Stage equipment installation must be completed in the decoration, right after the laying of the cable, audio and lighting equipment not only for the country more expensive, and many devices need to avoid contamination by dust, messy site decoration is not suitable for installation of equipment, equipment installation It should be noted first of all to carefully check out of the box, because many of the packaging of foreign equipment is standardized, there are a number of important spare parts or instructions may be individually isolated in the bottom of the box, it is easy to unpacking the box together with the throw; followed by equipment product before installation instructions should be read carefully in order to master the correct installation methods and procedures. For example; light bulbs and many computers are required to wear cotton coated gloves, glass installation, are not allowed to touch with bare hands; the final equipment installation is to be strong, protective measures must be in place, especially the lighting equipment, set high, the weight of large and to regular exercise, the general and the top of the stage or dance floor, so to be absolutely safe.

Fifth, the last is the power lines, control lines and signal lines connected. This is a serious need for detailed and technical work, so should be skillful and strong sense of responsibility of personnel in the line of connection, the first way to ensure that the requirements under the state without electricity, because the audio
and lighting equipment, power supply requirements different, if the installation to provide power, not only poor security, and easy to damage t

KTV灯光音响安装详细步骤介绍

he equipment
Second, requiring the construction meet the electrical installation practices, because the electrical installation rules to test whether a reasonable standard way, so whether or not in accordance with construction standards, to the quality of the project is completely different, many of the formal construction in accordance with standard engineering experts at a glance know the job done, "beautiful."
Speaking from the screen, the system capacity of the network interference, mainly on the system shielding and shielding is the correct person is not working, will be severe damage to equipment, while the supply line phase error may affect the speaker's phase, which correct and whether the level of quality screening, often found in a number of projects: either no mask or shield the formation of closed-loop; either the shielded cable connection error did not form the network can not resist interference shielding, and even some of the works of construction workers will signal to and power of zero, the shielding lines and signal lines confuse these essentials, random access, not only not anti-interference, but also bring a lot of interference, they must first actually put these concepts to understand clearly.

Sixth, the other is the installation, power lines, connecting the inspection. Because the sound engineer involved in the whole system connection points and connectors are more likely when the installation causes an error because of the individual, so careful examination is necessary, the general safety check including equipment installation, power supply lines are reasonable, the connectors is connected correctly, etc., there is another critical test items are: carefully check the status of each piece of equipment meets the design requirements set, this must not be forgotten, or easily result in equipment damage These states include; amplifier in the bridge request, the bridge switch is set; each device's power switch is the right choice; lights or electronic control device is a voice; address code scanners are set correctly; projector input settings, and more.

Seventh, to be sure the above construction steps are completed, the equipment should be ready to debug. For device debugging, as each project is different, it is difficult unity of a common approach, requires a separate discussion of classification, if it is to fully complete the engineering for all types of debugging
are introduced, the size will be too large, only the following commissioning of engineering equipment in general simply are introduced.